1994 CHEVROLET C10 recalls

K2 MOTOR IS RECALLING 1,921 AFTERMARKET HEADLAMPS OF VARIOUS MODELS SOLD FOR USE ON THE ABOVE LISTED VEHICLES. THESE HEADLAMPS ARE MISSING THE AMBER SIDE REFLEX REFLECTOR WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

WITHOUT THE AMBER SIDE REFLEX REFLECTORS, THE LIGHTING VISIBILITY MAY BE AFFECTED, POSSIBLY RESULTING IN A VEHICLE CRASH.

K2 MOTOR WILL NOTIFY OWNERS AND OFFER A FULL REFUND. THE RECALL BEGAN ON DECEMEBER 17, 2008. OWNERS MAY CONTACT K2 MOTOR AT 1-909-839-2992.

CERTAIN AAI MOTORSPORTS COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LIST PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

LACK OF AMBER SIDE REFLECTORS IN THE LAMPS WILL DECREASE LIGHTING VISIBILITY TO OTHER DRIVERS AND MAY POSSIBLY RESULT IN A VEHICLE CRASH

AAI MOTORSPORTS WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 1, 2006. OWNERS MAY CONTACT AAI MOTORSPORTS AT 909-923-9188.

SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.

DOPE, INC. IS RECALLING 42,540 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

DOPE, INC. WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON JULY 28, 2009. OWNERS MAY CONTACT DOPE, INC. AT 1-626-272-1798.

THE BRAKE PEDAL PUSH ROD RETAINER IS MISSING, MISPOSITIONED OR NOT PROPERLY SEATED.

BRAKE PEDAL PUSH ROD PROBLEMS CAN CAUSE THE STOP LAMPSWITCH AND THE BRAKE BOOSTER PUSH ROD TO DISCONNECT FROM THE BRAKE PEDAL,RESULTING IN LOSS OF BRAKE OPERATION, AND A VEHICLE CRASH COULD OCCUR WITHOUTPRIOR WARNING.

INSPECT VEHICLES TO ASSURE THE BRAKE PEDAL PUSH ROD RETAINER IS PRESENT AND FULLY SEATED IN ITS CORRECT POSITION.

THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLES COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.

DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.

TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.

IF THIS OCCURS, A LOSS OF VEHICLE CONTROL AND A CRASH COULD RESULT.

DEALERS WILL TIGHTEN THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TO THE PROPER TORQUE SPECIFICATION.

THE WINDSHIELDS WERE INSTALLED WITH INCORRECT WINDSHIELD OPENING PINCH-WELD-FLANGE PRIMER. THIS PRIMER WILL NOT PROPERLY ETCH THE PAINTED SURFACE OF THE FLANGE, ALLOWING THE WINDSHIELD TO SEPARATE FROM THE VEHICLE DURING A COLLISION. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 212, "WINDSHIELD MOUNTING."

CONSEQUENCE OF NON-COMPLIANCE: THE SEPARATION OF THE WINDSHIELD FROM THE VEHICLE DURING COLLISION INCREASES THE RISK OF INJURY FOR ALL PERSONS INVOLVED.

DEALERS WILL REMOVE THE WINDSHIELD AND REINSTALL IT USING THE CORRECT PRIMER.

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS, VANS AND MOTORHOMES EQUIPPED WITH ELECTRONICALLY FUEL INJECTED 6.5L DIESEL ENGINE. THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH FEDERAL REGULATION PART 573. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. THE CAMPAIGN WILL IMPROVE THE OVERALL DRIVEABILITY OF THESE VEHICLES.

CERTAIN VEHICLES CAN EXHIBIT SOME DRIVEABILITY CONCERNS SUCH AS POOR THROTTLE RESPONSE, STALLING, MISFIRE, POOR HOT OR COLD STARTING, EXTENDED CRANKING OF A HOT ENGINE, OR STALLING AFTER START. TRUCKS WITH MANUALTRANSMISSIONS CAN EXHIBIT POOR ACCELERATION FROM START OR COULD STALL DURING DECELERATION.

DEALERS WILL INSTALL SOME RECENTLY DEVELOPED ENHANCEMENTS WHICH WILL IMPROVE THE OVERALL DRIVEABILITY OF THESE VEHICLES.

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES, 2 AND 4-WHEEL DRIVE. SOLDER JOINTS NEAR THE WIRING HARNESS CONNECTOR CAN CRACK CAUSING THE WINDSHIELD WIPERS TO WORK INTERMITTENTLY.

THIS CONDITION CAN RESULT IN INOPERATIVE WIPERS, REDUCING A DRIVER'S VISIBILITY, AND INCREASING THE RISK OF A VEHICLE CRASH.

DEALERS WILL REPLACE THE WIPER MOTOR CIRCUIT BOARD AND COVER.

THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.

DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.

THESE VEHICLES WERE BUILT WITH FRONT SEAT BELT SYSTEMS WITH NO ENERGY MANAGEMENT LOOPS AND MAY NOT MEET THE HEAD INJURY CRITERIA REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANTS OF THESE SEATS MAY NOT BE PROPERLY RESTRAINED.

DEALERS WILL REPLACE THE RETRACTOR PORTION OF THE SEAT BELT ASSEMBLY(S) WITH ONE HAVING THE NEWLY DESIGNED ENERGY-MANAGEMENT TWIN-LOOP SYSTEM.

IF BOTH THE LAP-BELT AND SHOULDER-BELT ENERGY MANAGEMENT LOOPS ON THE FRONT SEAT BELT ASSEMBLIES RELEASE AT OR NEAR THE SAME TIME, ACCELERATION FORCES CAN CAUSE THE BUCKLE RELEASE MECHANISM TO ACTIVATE AND ALLOW THE BUCKLE TO SEPARATE FROM THE LATCH.

IF THE BUCKLE RELEASED, THE SYSTEM WOULD FAIL TO PROVIDE ADEQUATE OCCUPANT RESTRAINT PROTECTION.

DEALERS WILL REMOVE THE STITCHING THAT CREATES THE ENERGY MANAGEMENT LOOP IN THE SHOULDER BELT(S).

THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, "SEATING SYSTEMS."

THE MISSING BOLTS MAY CAUSE THE DRIVER'S SEAT TO BECOMELOOSE AND IN A SUDDEN STOP OR ACCIDENT MAY SUBJECT THE OCCUPANT TO INCREASEDRISK OF INJURY.

DEALERS WILL INSPECT SEATS FOR MISSING BOLTS AND INSTALL BOLTS IF REQUIRED.

VEHICLE DESCRIPTION: PICKUP TRUCKS, CREW CABS, UTILITY TRUCKS AND SPORT UTILITY VEHICLES. THESE VEHICLES WERE BUILT WITH THE POLARITY OF THE WIRING FOR THE ZERO ADJUST BRAKE SWITCH REVERSED FROM WHAT WAS SPECIFIED ON THE SWITCH DRAWING. WITH THE REVERSED POLARITY, THE CONTACTS IN THE BRAKE SWITCH CAN WEAR OUT PREMATURELY. THE BRAKE SWITCH WILL PERFORM NORMALLY UNTIL THE BRAKE SWITCH CONTACTS WEAR OUT, RESULTING IN LOSS OF THE BRAKE LAMPS WITHOUT ANY WARNING TO THE DRIVER.

THIS WOULD FAIL TO WARN A FOLLOWING DRIVER THAT THE VEHICLE IS BRAKING AND COULD LEAD TO A CRASH.

DEALERS WILL REPLACE THE BRAKE SWITCH AND REVERSE THE WIRING.