1991 VOLKSWAGEN JETTA recalls

SABERSPORT IS RECALLING 16,270 COMBINATION CORNER AND BUMPER LAMP ASSEMBLIES OF VARIOUS PART NUMBERS SOLD FOR USE AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES. THESE HEADLAMPS FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THESE LAMPS DO NOT CONTAIN THE REQUIRED AMBER SIDE REFLECTORS.

DECREASED LIGHTING VISIBILITY MAY RESULT IN A VEHICLE CRASH.

SABERSPORT WILL NOTIFY OWNERS AND OFFER A FULL REFUND FOR THE NONCOMPLIANT COMBINATION LAMPS. THE SAFETY RECALL BEGAN ON MAY 11, 2009. OWNERS MAY CONTACT SABERSPORT AT 1-909-598-7589.

CERTAIN HYDRAULIC BRAKE HOSES, P/N 171.611.107B, SOLD AS REPLACEMENT EQUIPMENT FOR 1975-1985 VOLKSWAGEN (VW) RABBIT; 1985-1992 VW GOLF; AND 1980-1992 VW JETTA PASSENGER VEHICLES. POSSIBLE BRAKE HOSE RUPTURE COULD OCCUR WHICH FAILS TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 106, "BRAKE HOSES."

BRAKE HOSE RUPTURE COULD RESULT IN LOSS OF BRAKING ABILITY, POSSIBLY RESULTING IN A VEHICLE CRASH.

FOREIGN PARTS DISTRIBUTORS WILL NOTIFY OWNERS AND REPLACE THE BRAKE HOSES WITH COMPLIANT BRAKE HOSES. THE RECALL BEGAN ON MARCH 30, 2006. OWNERS MAY CONTACT FOREIGN PARTS DISTRIBUTORS AT 305-885-8646 EXT. 11.

THE LOCK NUT OF THE CRUISE CONTROL ROD FOR THE OPERATING SERVO MAY NOT HAVE BEEN PROPERLY TORQUED DURING MANUFACTURE.

INADEQUATE TORQUE OF THE LOCK NUT COULD ALLOW THE RODADJUSTMENT TO CHANGE. THIS COULD INCREASE THE ENGINE IDLE SPEED, AND POSSIBLYINCREASE STOPPING DISTANCE WITH A POTENTIAL FOR A VEHICLE ACCIDENT.

CHECK AND ASSURE PROPER LOCK NUT TORQUE ON THE CRUISE CONTROL ROD.

THE FUEL HOSE ATTACHED TO THE FUEL DISTRIBUTION RAIL ON THE ENGINE MAY SHRINK BEYOND THE CLAMP FORCE OF THE FUEL HOSE CLAMPS, ALLOWING FUEL TO LEAK.

FUEL LEAKAGE IN THE ENGINE COMPARTMENT CAN CAUSE AN UNDERHOOD FIRE IF THE FUEL COMES IN CONTACT WITH A SOURCE OF IGNITION.

REPLACE THE FUEL HOSE ATTACHED TO THE FUEL RAIL AND INSTALL A NEW SPRING TYPE SELF-TIGHTENING CLAMP.

AN ENGINE PREHEATING TUBE MAY NOT BE PROPERLY SUPPORTED DUE TO A MISSING SUPPORT BRACKET, CAUSING THE PREHEATING TUBE TO CHAFE AGAINST THE RIGHT FRONT METAL BRAKE LINE. THIS CAN DAMAGE THE HYDRAULIC LINE, CAUSING BRAKE FLUID LEAKAGE AND DIMINISHED BRAKING IN ONE BRAKE CIRCUIT.

DIMINISHED BRAKING CAN RESULT IN INCREASED STOPPINGDISTANCES AND A POSSIBLE ACCIDENT.

DEALERS WILL INSTALL A PREHEATING TUBE SUPPORT BRACKET TO ENSURE PROPER POSITIONING RELATIVE TO THE RIGHT FRONT METAL BRAKE LINE.

THE VENTURI TUBE LOCATED IN THE THROTTLE VALVE HOUSING CAN BECOME LOOSE AND FALL AGAINST THE THROTTLE PLATE.

THE VENTURI TUBE CAN PARTIALLY BLOCK THE THROTTLE PLATEAND PREVENT IT FROM RETURNING TO ITS FULL IDLE POSITION, RESULTING IN UNWANTEDENGINE SPEED WHEN THE VEHICLE IS PLACED IN A FORWARD OR REVERSE GEAR.

REPLACE THE PRESS-FIT VENTURI TUBE WITH A THREAD TYPE TUBE.

FRONT BRAKE HOSES OF INSUFFICIENT LENGTH WERE INSTALLED IN SOME VEHICLES. THESE SHORT HOSES COULD STRETCH AND DEVELOP CRACKS.

THIS COULD RESULT IN BRAKE FLUID LEAKAGE, WITH LOSS OFFLUID PRESSURE AND BRAKING ABILITY.

REPLACE BOTH BRAKE HOSES.