2006 PETERBILT 387 recalls

PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1-940-591-4000. PACCAR's number for this recall is 215-D.

ON CERTAIN TRUCKS, THE FIFTH WHEEL KING PIN RELEASE AIR VALVE INTERNAL SPOOL WAS INSTALLED BACKWARDS. THE AIR OPTION OF THE KING PIN RELEASE SYSTEM WOULD BE INOPERABLE. TO CORRECT THIS SITUATION IN PRODUCTION, THE VEHICLE'S AIR LINES WERE MISTAKENLY REVERSED RATHER THAN REPLACING THE VALVE.

THERE IS A POSSIBILITY THAT THE KING PIN CAN RELEASE WITHOUT THE DRIVER'S KNOWLEDGE. WHEN THIS OCCURS, THE DRIVER COULD DRIVE AWAY AND THE TRAILER COULD BECOME DISENGAGED.

DEALERS WILL INSPECT THE FUNCTIONALITY OF THE KING PIN RELEASE SYSTEM AND SUSPECT VALVE. IF ANY VEHICLES HAVE A NON-CONFORMING VALVE OR INCORRECT PLUMBING, IT WILL BE REPLACED AND RE-PLUMBED. THE RECALL BEGAN ON FEBRUARY 28, 2007. OWNERS MAY CONTACT PETERBILT AT 940-591-4196.

ON CERTAIN TRACTORS EQUIPPED WITH CATERPILLAR DIESEL ENGINES, THE VARIABLE VALVE ACTUATION OIL LINE MAY WEAR AGAINST THE SHARP EDGE OF THE CYLINDER HEAD IF NOT POSITIONED CORRECTLY.

THE OIL LINE MAY BE CUT ON THE CYLINDER HEAD CAUSING AN OIL LEAK AND A POSSIBLE FIRE.

CATERPILLAR, IN CONJUNCTION WITH PACCAR, WILL BE CONDUCTING THE OWNER NOTIFICATION AND REMEDY FOR THIS CAMPAIGN FREE OF CHARGE. OWNERS MAY CALL CATERPILLAR AT 309-675-6496, KENWORTH AT 425-828-5440, OR PETERBILT AT 940-591-4201.

ON CERTAIN TRUCKS EQUIPPED WITH THE BENDIX ELECTRONIC STABILITY CONTROL (ESP) SYSTEM, THE SYSTEM USES MULTIPLE SENSORS AND AN ELECTRONIC CONTROL UNIT (ECU) TO CONTROL VEHICLE UNDER STEER, OVER-STEER, AND ROLLOVER SITUATIONS. THE SYSTEM RELIES ON VEHICLE SENSORS TO BE FUNCTIONING AND ALIGNED PROPERLY. THE STEERING ANGLE SENSOR HAS THE POTENTIAL TO BE MISALIGNED WITH THE STEERING COLUMN SHAFT, THEREBY PROVIDING INCORRECT INFORMATION TO THE BENDIX ECU.

THIS CONDITION COULD AFFECT VEHICLE THROTTLE CONTROL AND BRAKING, THEREBY LEADING TO LOSS OF VEHICLE STEERING CONTROL WHICH COULD CAUSE A CRASH WITHOUT WARNING.

BECAUSE OF THE IMMEDIATE AND SUBSTANTIAL RISK, KENWORTH AND PETERBILT DEALERS WILL FIRST DEACTIVATE THE YAW CONTROL FEATURE OF THE BENDIX ESP SYSTEM PREVENTING INADVERTENT ESP ACTIVATION. WHEN PARTS ARE AVAILABLE, THE STEERING COLUMN WILL BE REPLACED TO INSURE PROPER ALIGNMENT OF THE STEERING SHAFT SENSOR AND THE FULL ESP SYSTEM WILL BE REACTIVATED. THE RECALL BEGAN ON DECEMBER 7, 2005. PARTS TO COMPLETE THE REMEDY ARE ESTIMATED TO BE AVAILABLE IN EARLY 2006. OWNERS MAY CONTACT KENWORTH AT 1-425-828-5440 OR PETERBILT AT 1-940-591-4201.