1996 CHEVROLET G20 recalls

CERTAIN REPLACEMENT FUEL FILTERS, FRAM BRAND NAME P/N G3727, WITH DATE CODES X52911 THROUGH X60801 SEQUENTIALLY OR X600141 AND A MEXICO COUNTRY OR ORIGIN MARKING ON THE FUEL FILTER HOUSING MANUFACTURED FROM OCTOBER 18, 2005, THROUGH MARCH 21, 2006, SOLD FOR USE ON THE VEHICLES LISTED ABOVE AND ON CERTAIN SCHOOL BUSES. (TO SEE THE SCHOOL BUS ENGINE SIZES, CLICK ON "DOCUMENT SEARCH" AND THEN "BUS APPLICATIONS"). THE CONNECTOR ON THE FUEL FILTER WAS NOT MANUFACTURED TO HONEYWELL'S SPECIFICATION. AS A RESULT, THE O-RING MAY NOT SEAT CORRECTLY ON THE FUEL LINE.

THIS CONDITION MAY CAUSE AN INADEQUATE SEAL AT THE CONNECTION, POTENTIALLY LEADING TO A FUEL LEAK. IN THE PRESENCE OF AN IGNITION SOURCE, A FIRE COULD OCCUR.

HONEYWELL WILL NOTIFY OWNERS AND REPLACE THE FUEL FILTERS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 18, 2006. OWNERS MAY CONTACT FRAM CUSTOMER SERVICE AT 1-800-890-2075 (OPTION 1).

CERTAIN HONEYWELL FRAM RACING BRAND HP4 AND HP8 OIL FILTERS THAT WERE MANUFACTURED FROM MAY 25, 2006, THROUGH SEPTEMBER 14, 2007, AND SOLD FOR USE AS REPLACEMENT EQUIPMENT FOR VEHICLES LIST ABOVE. THE AFFECTED FILTERS ARE MARKED WITH A DATE CODE A61451 THROUGH A72571 SEQUENTIALLY. THE DATE CODE AND PART NUMBER APPEAR ON THE FILTER HOUSING. FRAM RACING HP4 AND HP8 OIL FILTERS NOT BEARING A DATE CODE IN THIS RANGE ARE NOT AFFECTED BY THIS RECALL. THE GASKET OF THE OIL FILTER BECOMES MORE PLIABLE UNDER HIGH TEMPERATURES AND PRESSURES.

THIS CONDITION MAY CAUSE INADEQUATE SEALING AND LOSS OF ENGINE OIL, POSSIBLY RESULTING IN A FIRE.

HONEYWELL WILL REPLACE THE AFFECTED OIL FILTERS FREE OF CHARGE. THE RECALL BEGAN DURING NOVEMBER 2007. OWNERS CAN CONTACT FRAM CUSTOMER SERVICE TOLL-FREE AT 1-800-890-2075.

THE STEERING LINKAGE ASSEMBY CONTAINS A RELAY ROD TAPERED-STUD ATTACHMENT NUT THAT WAS NOT TORQUED TO PROPER SPECIFICATIONS.

THE TAPERED STUD CAN LOOSEN AND THE DRIVER WOULD NOTICE A LAG IN THE RESPONSIVENESS TO STEERING WHEEL INPUTS. EVENTUALLY THE RELAY ROD STUD CAN FRACTURE RESULTING LOSS OF STEERING CONTROL.

DEALERS WILL REMOVE THE EXISTING CRIMPED NUT AND INSTALL A NEW NUT TORQUED TO SPECIFICATIONS.

WATER INTRUSION INTO THE KICK PANEL AREAS IN FRONT OF BOTH THE DRIVER AND PASSENGER DOORS CAN CAUSE A CORROSION PATH BETWEEN THE BATTERY FEED AND THE ELECTRICAL GROUND.

THIS CONDITION CAN CAUSE AN ELECTRICAL SHORT LEADING TO IGNITION AND COMBUSION OF THE PLASTICS IN THE ELECTRICAL COMPONENTS OF THE VEHICLE RESULTING IN A VEHICLE FIRE.

DEALERS WILL REPLACE THE 25 AMP CIRCUIT BREAKERS WITH 25 AMP FUSES IN THE FUSE BLOCK; REMOVE A TEMPORARY PAPER FUSE-BLOCK COVER; INSTALL A PLASTIC SHIELD OVER THE FUSE BLOCK; REPLACE AND REORIENT THE POWER DOOR LOCK RELAY (IF EQUIPPED); INSPECT THE REMOTE KEYLESS ENTRY MODULE (IF EQUIPPED) FOR SIGNS OF CORROSION, REPLACE IF CORRODED, AND REORIENT IT; AND APPLY ADDITIONAL BODY SEALER IN KEY AREAS.

THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH THE SAFETY ACT. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. VEHICLE DESCRIPTION: CERTAIN LIGHT DUTY PICKUP TRUCKS, SPORT UTILITY VEHICLES, OR MINIVANS EQUIPPED WITH 3-SENSOR ABS (ANTILOCK BRAKING SYSTEM) EBC4 UNITS.

THESE VEHICLES CAN EXPERIENCE EXTENDED STOPPING DISTANCES DURING ABS STOPS ON CERTAIN MULTIPLE SURFACES, INCREASING THE RISK OF A CRASH.

DEALERS WILL MODIFY THE COMPUTER PROGRAM WHICH OPERATES THE ABS UNIT ON SOME VEHICLES, OR REPLACE THE COMPUTER ON OTHERS TO IMPROVE THE PERFORMANCE OF THE ABS ON THESE SURFACES.