1994 Freightliner Fld recalls

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS CONVERTED FROM SLEEPER CABS TO DAY CABS FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES."

THE SEAT OCCUPANT MAY NOT BE PROPERLY RESTRAINED IN THE EVENT OF A CRASH.

DEALERS WILL INSTALL REINFORCEMENTS TO THE SEAT BELT ANCHORAGES. OWNER NOTIFICATION BEGAN DECEMBER 31, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FREIGHTLINER AT 1-800-547-0712.

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH HORTON FAN DRIVES. THE FAN DRIVE CONTROL SYSTEM WAS RECONFIGURED WHICH RESULTED IN A SIGNIFICANT INCREASE IN THE DEMAND FOR FAN ACTIVATION AND ASSOCIATED STRESS TO ELECTRICAL AND MECHANICAL COMPONENTS. VARIOUS COMPONENT FAILURE MODELS, COMBINED WITH CHARACTERISTICS OF THE FAN CLUTCH AND ITS BEARINGS, CAN CAUSE FAN CLUTCH BEARINGS TO FAIL PREMATURELY AND RESULT IN A LOCKED FAN.

IF THE FAN IS LOCKED, THE THE SYSTEM CALLS FOR THE FAN TO BE ON, THE FAN CLUTCH WILL SLIP, GENERATE HEAT, AND UNLESS RELEASED, WILL RESULT IN A FIRE.

DEALERS WILL REPLACE THE FAN CLUTCH DRIVE DISC WITH ONE THAT INCORPORATES A THERMALLY ACTIVATED PRESSURE RELIEF.

VEHICLE DESCRIPTION: HEAVY DUTY TRUCK. THE SHOULDER BOLT WHICH HOLDS THE GROTE TURN SIGNAL SWITCH CASE AND COMPONENTS TOGETHER CAN LOOSEN RESULTING IN THE TURN SIGNAL MALFUNCTIONING.

IF THE TURN SIGNAL FUNCTION IS LOST, FOLLOWING MOTORISTS WOULD NOT BE AWARE OF THE TURNING VEHICLE, INCREASING THE RISK OF A VEHICLE CRASH.

DEALERS WILL INSPECT THESE VEHICLES AND TIGHTEN ANY LOOSE BOLTS AND IN THE TURN SIGNAL SWITCH WITHIN 2 YEARS FROM THE DATE OF THE RECALL NOTIFICATION LETTER. THE SHOULDER BOLT WILL BE REMOVED, CLEANED, AND REINSTALLED WITH LOCTITE. OWNERS CAN ALSO REQUEST LOCTITE AND REPAIR INSTRUCTIONS SO THEY CAN FIX THE VEHICLES THEMSELVES.

THE GLASS IN THE SWING-OUT SIDE WINDOW CAN SEPARATE FROM THE WINDOW FRAME.

THE GLASS SEPARATING FROM THE FRAME CAN CAUSE PERSONAL INJURY OR A HAZARD TO OTHER VEHICLES IF SEPARATION OCCURS WHILE THE TRUCKIS IN MOTION.

DEALERS WILL REPLACE THE SWING-OUT SIDE WINDOWS WITH A SIDE WINDOW RETAINED BY ADHESIVE.

THE MUFFLER MOUNTING BRACKETS THAT ATTACH THE EXHAUST SYSTEM AND CAB ENTRY GRAB HANDLE TO THE CAB WERE MANUFACTURED WITH INCOMPLETE WELDS.

AN INCOMPLETE WELD COULD CAUSE A PERSON USING THE GRABHANDLE TO SLIP AND FALL RESULTING IN PERSONAL INJURY.

DEALERS WILL INSPECT VEHICLES FOR ADEQUATE MUFFLER BRACKET WELDS AND RE-WELD IF NECESSARY.

AIR SYSTEM BLOCKAGE IN THE AIR DRYER OCCURS DEGRADING THE MOISTURE REMOVING CAPABILITIES OF THE DRYER WHEN THE VEHICLE IS OPERATED IN A COLD ENVIRONMENT AND MOISTURE ACCUMULATES AND FREEZES IN THE AIR DRYER OR IN THE LINE BETWEEN THE DRYER AND THE AIR SYSTEM RESERVOIR. THE AIR DRYER CAN BECOME OVER PRESSURIZED CAUSING THE AIR DRYER CARTRIDGE TO SEPARATE FROM THE MOUNTING BASE.

IF THE AIR DRYER SEPARATES FROM THE BASE, THE CARTRIDGECAN SEPARATE SUFFICIENTLY ENOUGH TO CAUSE PERSONAL INJURY OR PROPERTY DAMAGE.

DEALERS WILL EQUIP AIR SYSTEMS WITH A PRESSURE RELIEF VALVE TO BE LOCATED BETWEEN THE COMPRESSOR AND THE AIR DRYER. THIS PRESSURE RELIEF VALVE IS INTENDED TO VENT IF EXCESSIVE PRESSURE DEVELOPS IN THE AIR DRYER.